Content © 2012-2017 by American IronHorse Owners Organization.  Use of AIH Logo Licensed by American Ironhorse, LLC
NOTE:   Technical Information content is intended to help fellow members and is not here to be copied and sold.
Connector-to-Connector Table
by “MC7”
Follow Wiring From Connector to Connector Here’s a table showing the wiring flow for AIH Motorcycles from 2005 - 2007 (see table for effectivity). This table is a short cut to how things are connected to each other, and what the funtion is for each wire on each connector.  It also shows the flow of voltage from source to destination which will be helpful when using a Volt- Ohm Meter (VOM) or test light to probe connector pins, switch contacts, etc. If used along with an appropriate schematic drawing, this may help make wiring easier to follow when troubleshooting electrical issues. Table as a PDF: Table as an Excel spreadsheet: The table includes wire color, purpose (functionality), and flow.  See the table for info on the use of arrowheads (">" and "<") to denote the flow from connector to connector and from device to device. In a few instances, different wires with different colors are connected together, so in these instances there are multiple colors shown. Here's an example on how to interpret the table: Connector half "40A" goes to the "Devices" which are the "Right Hand Control Switches" "Function". ("A" half always goes to the devices). The other half "40B" comes from the "Harness". ("B" half always goes to the harness). This connector has 6 pins. Note: In some connectors, the pin may exist in one half and be plugged in opposite half, or the connector pins may be absent (not populated) from the holes in the plastic connector shell. Also, some connectors (the three pin connectors and one two pin connector) do not have pin numbers, they are "A, "B", and "C" (or "A" and "B"), hence the inclusion of these letters in the heading's first three pins: "Pin 1 (or A)" etc. Pin 1 - The Harness side of the connector has an Orange wire with a White stripe, and has +12v on it coming from (< = sourced by) the RHC, pin # [26]. The Devices side of the connector carries the +12v through an Orange wire with a White stripe to (< = goes to) the Right hand control SWitches. In summary, the RHC pin #26 feeds +12v to connector 40B/A and provides +12v power to all of the switches on the right handlebar. I believe the information to be as accurate as it can be with the resources available. As always, use it knowing there could be errors; should you find errors, please advise so they can be corrected. Hopefully, you may find this useful.
ORGANIZATION ORGANIZATION OWNERS OWNERS For All American Ironhorse Motorcycle Owners
Connectors
© 2012-2017   American IronHorse Owners Organization Use of AIH Logo Licensed by American Ironhorse, LLC 
NOTE:   Technical Information content is intended to help fellow members and is not here to be copied and sold.
Connector-to-Connector Table
by “MC7”
Follow Wiring From Connector to Connector Here’s a table showing the wiring flow for AIH Motorcycles from 2005 - 2007 (see table for effectivity). This table is a short cut to how things are connected to each other, and what the funtion is for each wire on each connector.  It also shows the flow of voltage from source to destination which will be helpful when using a Volt- Ohm Meter (VOM) or test light to probe connector pins, switch contacts, etc. If used along with an appropriate schematic drawing, this may help make wiring easier to follow when troubleshooting electrical issues. Table as a PDF: Table as an Excel spreadsheet: The table includes wire color, purpose (functionality), and flow.  See the table for info on the use of arrowheads (">" and "<") to denote the flow from connector to connector and from device to device. In a few instances, different wires with different colors are connected together, so in these instances there are multiple colors shown. Here's an example on how to interpret the table: Connector half "40A" goes to the "Devices" which are the "Right Hand Control Switches" "Function". ("A" half always goes to the devices). The other half "40B" comes from the "Harness". ("B" half always goes to the harness). This connector has 6 pins. Note: In some connectors, the pin may exist in one half and be plugged in opposite half, or the connector pins may be absent (not populated) from the holes in the plastic connector shell. Also, some connectors (the three pin connectors and one two pin connector) do not have pin numbers, they are "A, "B", and "C" (or "A" and "B"), hence the inclusion of these letters in the heading's first three pins: "Pin 1 (or A)" etc. Pin 1 - The Harness side of the connector has an Orange wire with a White stripe, and has +12v on it coming from (< = sourced by) the RHC, pin # [26]. The Devices side of the connector carries the +12v through an Orange wire with a White stripe to (< = goes to) the Right hand control SWitches. In summary, the RHC pin #26 feeds +12v to connector 40B/A and provides +12v power to all of the switches on the right handlebar. I believe the information to be as accurate as it can be with the resources available. As always, use it knowing there could be errors; should you find errors, please advise so they can be corrected. Hopefully, you may find this useful.
ORGANIZATION ORGANIZATION OWNERS OWNERS
Connectors